Product Name:
THINVERT® Concentrate
Chemical Name:
Not applicable: blend
Chemical Family:
Synthetic Isoparaffinic Hydrocarbon mixed with emulsifiers and nonionic surfactant blend
1. INGREDIENTS: (%w/w, unless otherwise noted)
Isoparaffinic Hydrocarbon Blend
Other ingredients, including: Proprietary Emulsifiers and Surfactants
|
97.75%
2.25%
|
2. PHYSICAL DATA:
BOILING POINT: 433 to 484 degrees F.
HEALTH INFORMATION AND PROTECTION:
GENERAL:
No toxicity information is available on this specific preparation; this health hazard assessment is based on information that is available on its components.
EYE CONTACT:
Slightly irritating, but does not injure eye tissue.
SKIN CONTACT:
Frequent or prolonged contact may irritate and cause dermatitis. Low order of toxicity.
INHALATION:
High vapor/aerosol concentrations (greater than 700 ppm, attainable at elevated temperatures well above ambient) are irritating to the eyes and respiratory tract, and may cause headaches, dizziness, anesthesia, drowsiness, nausea, and mucous membrane irritation of eyes, nose throat and respiratory passages.
INGESTION:
Small amounts of this product aspirated into the respiratory system during ingestion or vomiting may cause mild to severe pulmonary injury. Minimal toxicity.
3. FIRST AID
EYE CONTACT:
Flush with large amounts of water until irritation subsides. If irritation persists, get medical attention.
SKIN CONTACT:
Remove contaminated clothing and footwear. Was skin with large amounts of soap and water. Wash contaminated clothing and decontaminate footwear before reuse.
INHALATION:
Remove victim to fresh air. If cough or other respiratory problems develop, get medical attention.
INGESTION:
If swallowed, do not induce vomiting. Keep at rest. Get prompt medical attention.
4. FIRE AND EXPLOSION HAZARD:
FLASH POINT: 200 degrees F, 93.4 degrees C.
AUTOIGNITION TEMPERATURE: No Data
GENERAL HAZARD:
Some components of this product are combustible and may form combustible mixtures at or above the flashpoint. Empty container retains product residue. Keep away from heat, sparks or flame. Do not weld or use a cutting torch near container. Do not distribute, make available, furnish, or reuse empty container except for storage and shipment of original product. Empty drums should be completely drained and reconditioned or properly disposed of.
FIRE FIGHTING:
Use water spray to cool fire-exposed surfaces and protect personnel. Isolate fuel supply from fire.
Use foam, dry chemical, or water spray to extinguish fire.
HAZARDOUS COMBUSTION PRODUCTS: No Unusual
5. REGULATORY INFORMATION:
TSCA: All ingredients are on the TSCA Inventory
6. REACTIVITY DATA:
STABILITY: Stable
HAZARDOUS POLYMERIZATION: Will not occur
MATERIALS AND CONDITIONS TO AVOID INCOMPATIBILITY: Strong oxidizing agents
HAZARDOUS DECOMPOSITION PRODUCTS: None
7. STORAGE AND HANDLING:
STORAGE TEMPERATURE: Ambient
LOADING / UNLOADING TEMPERATURE: Ambient
STORAGE / TRANSPORT PRESSURE: Atmospheric
Note: In containers of 119 gallons capacity or less, this product is not regulated by DOT.
8. SPILL OR LEAK PROCEDURES:
Wear skin , eye and respiratory protection during cleanup. Soak up liquid with absorbent and shovel into waste container. Cover container and remove from work area. Wash residue from spill area with hot water containing a detergent and flush to a sewer serviced by a wastewater treatment facility.
DISPOSAL METHOD: Discarded product is not a hazardous waste under RCRA, 40 CFR 261.
CONTAINER DISPOSAL: Empty container retains product residue. Keep away from heat, sparks or flame. Do not weld or use a cutting torch near container. Do not distribute, make available, furnish, or reuse empty container except for storage and shipment of original product. Return for refilling if service is available. Remove all product residue and puncture or otherwise destroy empty container before disposal.
The preceding information is given in good faith, but no warrenty, express or implied, is made. Reviewed 01/13/93. Revised 09/02/98.